[ Home > T-HAWK PARTS ]
T-HAWK PARTS |
| ||
| Propeller | |
| ||
| ||
| Wing Includes rubberband set | |
| ||
| ||
| Neon Green Sport Wing This new green version of the standard orange T-Hawk wing is slightly thicker for increased robustness at high speeds. Easily identifies your T-Hawk when flying with another! Includes rubber band set. Now Shipping! | |
| ||
| ||
| T-HAWK 58" Training Wing w/Tension Wire This wing is ideal to reduce flying speed for easier learning! Fabricated by splicing 3 sections of the standard high performance wing reinforced with wood and carbon fiber rods. A nylon tension wire is now included to provide additional curvature and stiffness for improved handling and responsiveness. The extra 17" in length provides an additional 39 sqin of lift area with only 2.5 oz weight increase. Inset photo shows standard wing resting on top of the training wing for size comparison only. Ships UPS Ground Separately Out of Stock - Order Pending | |
| ||
| ||
| Wing Bands Pkg of 10 Replacement rubberbands for T-Hawk. Package of 10. Two are required for attaching the standard wing. The longer Trainer wing requires 4. | |
| ||
| ||
| Wing Attach Post Set Post length for T-Hawk, but may be trimed for SkySeeker and Predator. All Plastic. End caps must be epoxied after assembly. | |
| ||
| ||
| Tension Wire Replacment for 58" Wing Provides additional curvature and stiffness for improved handling and responsiveness. Monofilament nylon line for high strength and elasticity. Includes installation instructions. | |
| ||
| ||
| Tail | |
| ||
| ||
| Elevator Stab | |
| ||
| ||
| Rudder T-HAWK Rudder Replacement | |
| ||
| ||
| T-HAWK NiCd 8.4V 600mAh With Heavy Duty Tamiya Connector Type | |
| ||
| ||
| T-HAWK NiMH 8.4V 1000mAh KAN Brand Premium Quality and Perfomance NiMH battery pack for R/C flight featuring high discharge capability and low internal resistance. With Standard Size Tamiya Connector (Heavy Duty). | |
| ||
| ||
| High Performance 480 Motor Hop-up Hop-up your T-Hawk to 480 power for more speed and aerobatic abilities like torque rolls! Designed for T-Hawk using premium magnetics with case sleeve to provide 10-15% more power than economy 480's. Compatible with T-Hawk speed controllers with flat spade connectors. Installation Note. The black or blue motor wire connects to the terminal marked with a RED dot, otherwise the propeller will spin in the wrong direction. Be sure to press the connector far enough to hear it lock. Flat Spade Disconnect
Tip | |
| ||
| ||
| 380 Motor Standard Direct replacement for T-Hawk. | |
| ||
| ||
| Light Duty Landing Gear Set | |
| ||
| ||
| Heavy Duty Landing Gear Set This heavy duty T-HAWK landing gear is sure to out last anything else. The JUMBO 2.5" foam wheels will make take-offs easier on pavements with expansion joints, coarse asphalts and unpaved surfaces. Attaches to the fuselage using the 4 rear servo platform screws. See the inset photo. Orient the landing gear so the tapered edge is leading, and the straight edge trailing. This places the C.G. point closest to the wing. | |
| ||
| ||
| Housing with Tailboom and Hardware This special Housing/Tailboom combo value comes complete with most hardware installed. See inset for loose hardware items. Even includes receiver retainer band. Note this Fuselage Assembly is for standard T-HAWK versions. See T-Hawk Trainer Part Replacements if you purchased a Training Package with Buddy-Box Radio Sets. | |
| ||
| ||
| Housing Includes Hardware | |
| ||
| ||
| Tail Boom Includes tail bracket and heat shrink sleeve. | |
| ||
| ||
| FM 27MHz Fuselage Assy This assembly is complete with,ESC,servos, pushrods and motor installed. The FM receiver is optional. The tail boom contains the plastic bracket on the end. Note this Fuselage Assembly is for standard T-HAWK versions. See T-Hawk Trainer Fuselage replacements if you purchased a Training Package with Buddy-Box Radio Sets. | |
| ||
| ||
| Servo Tray | |
| ||
| ||
| Speed Controller 7C4 Replacement for T-Hawks with flat spade motor connectors. Arms with a 1 sec zero throttle hold. For use with 7cell NiCd or NiMH packs with standard size Tamiya connector and motors with flat spade type connectors. | |
| ||
| ||
| Speed Controller II Replaces the push button types with pin type motor connectors for T-Hawks and Predators. Arming occurs after a 3 second hold on zero throttle. Pin type motor connections and standard size Tamiya battery connector. Jumper configurable for partial and full throttle ranges (Transmitter Dependent). Recommended for generation II ReadyToFlyFun Transmitters (Generation II marking indicated on the back label) and all other brands (HiTec/GWS/JR/Futaba/Airtronics). | |
| ||
| ||
| Click Here for Complete Parts List by Category | |
|
|
